精品国产99久久久久久www_亚洲精彩视频在线观看的_性欧美婬妇ⅹxxx视频_里番肉工口全彩老师_a天堂最新在线观看_精品国产在天天在线观看_免费看那种视频_樱桃电视剧全集播放_成人性视频免费看的鲁片_中国伦理影院

General description

The LPC2194 is based on a 16/32-bit ARM7TDMI-S CPU with real-time emulation and

embedded trace support, together with 256 kB of embedded high-speed flash memory. A

128-bit wide memory interface and a unique accelerator architecture enable 32-bit code

execution at maximum clock rate. For critical code size applications, the alternative 16-bit

Thumb mode reduces code by more than 30 with minimal performance penalty.

With its compact 64-pin package, low power consumption, various 32-bit timers,

4-channel 10-bit ADC, four advanced CAN channels, PWM channels and 46 fast GPIO

lines with up to nine external interrupt pins this microcontroller is particularly suitable for

automotive applications such as a CAN gateway that connects several CAN busses or a

CAN bridge between sub networks at different speeds. Sensors with CAN interface or

debugging via CAN are additional applications that need more than two CAN interfaces. It

is also an adequate solution for industrial control, medical systems and fault-tolerant

maintenance buses. With a wide range of additional serial communications interfaces, it is

also suited for communication gateways and protocol converters as well as many other

general-purpose applications.

Remark: Throughout the data sheet, the term LPC2194 will apply to devices with and

without the /00 or /01 suffixes. The /00 or the /01 suffix will be used to differentiate from

other devices only when necessary.

Features and benefits

2.1 Key features brought by LPC2194/01 devices

? Fast GPIO ports enable port pin toggling up to 3.5 times faster than the original device.

They also allow for a port pin to be read at any time regardless of its function.

? Dedicated result registers for ADC(s) reduce interrupt overhead. The ADC pads are

5 V tolerant when configured for digital I/O function(s).

? UART0/1 include fractional baud rate generator, auto-bauding capabilities and

handshake flow-control fully implemented in hardware.

? Buffered SSP serial controller supporting SPI, 4-wire SSI, and Microwire formats.

? SPI programmable data length and master mode enhancement.

? Diversified Code Read Protection (CRP) enables different security levels to be

implemented. This feature is available in LPC2194/00 devices as well.

? General purpose timers can operate as external event counters.

2.2 Key features common for all devices

? 16/32-bit ARM7TDMI-S microcontroller in a tiny LQFP64 package.

? 16 kB on-chip SRAM and 256 kB on-chip flash program memory. 128-bit wide

interface/accelerator enables high speed 60 MHz operation.

? In-System Programming (ISP) and In-Application Programming (IAP) via on-chip

bootloader software. Flash programming takes 1 ms per 512 B line. Single sector or

full chip erase takes 400 ms.

? EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with

on-chip RealMonitor software as well as high speed real-time tracing of instruction

execution.

? Four interconnected CAN interfaces with advanced acceptance filters. Additional serial

interfaces are two UARTs (16C550), Fast I2C-bus (400 kbit/s) and two SPIs.

? Four channel 10-bit ADC with conversion time as low as 2.44 ?s.

? Two 32-bit timers (with four capture and four compare channels), PWM unit (six

outputs), Real-Time Clock and Watchdog.

? Vectored Interrupt Controller with configurable priorities and vector addresses.

? Up to forty-six 5 V tolerant general purpose I/O pins. Up to nine edge or level sensitive

external interrupt pins available.

? Operating temperature range from ?40 ?C to +125 ?C.

? 60 MHz maximum CPU clock available from programmable on-chip Phase-Locked

Loop with settling time of 100 ?s.

? On-chip crystal oscillator with an operating range of 1 MHz to 30 MHz.

? Two low power modes, Idle and Power-down.

? Processor wake-up from Power-down mode via external interrupt.

? Individual enable/disable of peripheral functions for power optimization.

? Dual power supply:

? CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ? 0.15 V).

? I/O power supply range of 3.0 V to 3.6 V (3.3 V ? 10 ) with 5 V tolerant I/O pads.